Precision Micro-Coaxial Interconnects · 0.30 mm to 0.50 mm Pitch
Custom MIPI CSI-2 & Micro-Coaxial Camera Cable Assemblies
HiFlexlinK engineers high-frequency mipi cable and csi 2 cable harnesses built for low-EMI image transmission across UAV gimbals, embedded vision modules, and industrial displays. Whether you require an ultra-flexible mipi camera cable with 0.30 mm pitch Hirose DF56 terminations, a 20-pin hdzero mipi cable for digital FPV VTX links, or cross-brand assemblies linking a mipi csi 2 cable to a mipi to parallel interface bridge board, every unit is precision-crimped, impedance-verified, and ready for rapid prototyping.
Engineering Capability Envelope
Supported Contact Pitch 0.30 mm / 0.40 mm / 0.50 mm
Micro-Coaxial Wire Range #36 AWG to #48 AWG (UL1354)
Pin Configurations: 10P / 20P / 26P / 30P / 40P / 50P
Controlled Impedance: 50 Ohm +/- 5% (Up to 10 Gbps)
Connector Families: I-PEX, Hirose DF56, KEL USL20, ACES
Prototype Turnaround: 5–10 Business Days
0.30–0.50 mm
Fine-Pitch Termination
Automated micro-stripping and precision solder bar assembly
<= 0.3 dB/cm
Low Insertion Loss @ 5 GHz
Dual-layer foil and braid shielding for clean eye diagrams
100% Tested
Continuity & Pull-Force QC
Netlist open/short screening plus AC 200 V hipot checks
15,000+/wk
Scalable OEM Capacity
Seamless transition from low-MOQ samples to mass production
HiFlexlinK Part Number Nomenclature Guide
Every HiFlexlinK assembly follows a structured five-segment identifier specifying the connector family, active pin count, contact pitch, and micro-coaxial wire gauge. Select any segment below to inspect ordering parameters.
HFL
Brand Prefix
MC345
Connector series
30P
Pin Counts
P04
Pitch(mm)
AWG42
wire Gauge
01. Brand Series Prefix
Identifies HiFlexlinK precision micro-coaxial and high-speed MIPI harness assemblies.
Code: HFL
02. Connector Family Code
Defines the mating plug or hybrid pair (I-PEX, Hirose DF56, KEL USL20, ACES, or HDZero VTX).
MC345 · MC846 · DF56 · MC454A · KUSL20 · MC878 · HDZ20
03. Active Pin Count
Specifies standard populated contacts; custom pinouts from 10P to 50P available per series.
20P · 26P · 30P · 40P · 50P
04. Contact Pitch Code
Centerline terminal spacing in tenths of a millimeter for fine-pitch board matching.
P03 (0.30 mm) · P04 (0.40 mm) · P05 (0.50 mm)
05. Wire Gauge (AWG)
Standard micro-coaxial conductor size; configurable from #36 AWG up to #48 AWG.
AWG40 · AWG42 · AWG44 · AWG46
HiFlexlinK MIPI & Micro-Coaxial Product Catalog
Compare all seven standardized HFL cable assemblies by connector architecture, contact pitch, pin count, wire gauge, and electrical rating. Filter by application or switch to the specification matrix for side-by-side engineering review.
0.40 mm Pitch Micro-Coax
Drone & Camera CSI · 0.40 mm Pitch
HFL-MC345-30P-P04-AWG42
MIPI CSI-1 / CSI-2 Micro-Coaxial Camera Cable Assembly
Engineered for UAV drone cameras and compact HD imaging payloads requiring horizontal low-profile mating.
0.50 mm Pitch Micro-Coax
High-Speed DSI & eDP · 0.50 mm Pitch
HFL-MC846-20P-P05-AWG40
0.50 mm Pitch 20-Pin MIPI DSI / LVDS / eDP Micro-Coax Assembly
High-bandwidth display and camera interconnect supporting MIPI Gear 3 and eDP HBR3 data rates.
0.30 mm Pitch DF56
Image Sensor · 0.30 mm Pitch
HFL-DF56-26P-P03-AWG42
0.30 mm Pitch 26-Pin Ultra-Fine Image Sensor Micro-Coaxial Cable
Ultra-compact CSI-2 cable assembly tailored for space-constrained CMOS image sensors and optical heads.
0.40 mm Hybrid Assembly
High-Speed DSI & eDP · 0.40 mm Pitch
HFL-MC454A-30P-P04-AWG40
0.40 mm Pitch I-PEX 20454 to ACES 88441 Hybrid MIPI / eDP Cable
Cross-brand harness connecting MIPI DSI/CSI hosts, eDP panels, and MIPI to parallel interface bridge PCBs.
KEL USL20 0.40 mm
Image Sensor · 0.40 mm Pitch
HFL-KUSL20-30P-P04-AWG42
KEL USL20-30SS-0045-C 0.40 mm Pitch MIPI Camera & Display Cable
Dedicated 30-pin MIPI camera cable built for Sony camera blocks and industrial LVDS display connectors.
50 Ohm Shielded 40AWG
High-Speed DSI & eDP · 0.40 mm Pitch
HFL-MC878-30P-P04-AWG40
30-Pin 50-Ohm Dual-Shielded 40AWG MIPI / LVDS Micro-Coaxial Assembly
Impedance-controlled 10 Gbps harness with dual-layer foil + braid shielding for noisy RF environments.
20P HDZero MIPI Cable
Drone & Camera CSI · 0.40 mm Pitch
HFL-HDZ20-20P-P04-AWG42
20-Pin Digital HDZero FPV VTX & MIPI Camera Micro-Coaxial Cable
Low-latency digital HD video HDZero MIPI cable built for Race V2 VTX, Shark Byte, and long-range FPV wings.
| HiFlexlinK Part Number | Connector / Mating Interface | Pitch | Pin Count | Wire Gauge (AWG) | Length | Action |
|---|---|---|---|---|---|---|
| HFL-MC345-30P-P04-AWG42 | I-PEX 20345-030T-32R (Horizontal) | 0.40 mm | 30P (10–40P) | #40 / #42 / #44 / #46 | Custom | RFQ |
| HFL-MC846-20P-P05-AWG40 | I-PEX 20846 / 20847-020T-02 (Mates 20849) | 0.50 mm | 20P (20–40P) | #36–#46 (#32/#34 Pwr) | Custom | RFQ |
| HFL-DF56-26P-P03-AWG42 | Hirose DF56-26P-0.3SD (662-5604-1) | 0.30 mm | 26P (26–50P) | #38–#46 (Rec. #42–#46) | Custom | RFQ |
| HFL-MC454A-30P-P04-AWG40 | I-PEX 20454-030T to ACES 88441 | 0.40 mm | 30P / 40P (10–50P) | #38 / #40 / #42 / #44 / #46 | Custom | RFQ |
| HFL-KUSL20-30P-P04-AWG42 | KEL USL20-30SS-0045-C | 0.40 mm | 30P | #42 Std (#38–#46) | Custom | RFQ |
| HFL-MC878-30P-P04-AWG40 | I-PEX 20878-030T-01 (1:1 Shielded) | 0.40 mm | 30P | UL1354 40AWG (50 Ohm) | Custom | RFQ |
| HFL-HDZ20-20P-P04-AWG42 | Race V2 / Shark Byte VTX & HDZero Camera | 0.40 mm | 20P | #40 – #48 AWG | 40/80/120/250 mm | RFQ |
No HiFlexlinK assemblies match your current filter criteria.
Precision Manufacturing, Electrical Testing & Compliance
Fine-pitch micro-coaxial termination demands repeatable mechanical retention and verified RF signal integrity. Every HiFlexlinK assembly is produced in controlled lines with full electrical and environmental screening.
100%
Continuity & Pull-Force Screening
Automated multi-point continuity, open/short, and AC 200 V dielectric withstand testing on every cable, paired with destructive tensile pull-force sampling on each lot.
50 Ohm +/- 5%
TDR Impedance & Insertion Loss
Dual-layer foil and braided ground return shielding controls differential skew and keeps insertion loss at or below 0.3 dB/cm at 5 GHz for 10 Gbps links.
40–500 mm+
Custom Length & Hybrid Pinouts
Exact millimeter length cutting, braided sleeve or Kapton wrapping, and custom cross-brand terminations tailored to your PCB layout and chassis geometry.
RoHS / REACH
Flexible MOQ & Rapid Prototyping
UL1354 micro-coaxial materials rated from -40°C to +105°C, RoHS and REACH compliant, with 2–10 day engineering samples and scalable production MOQ.
Engineering Selection & Procurement FAQ
Technical guidance on connector compatibility, AWG sizing, signal integrity, and prototype fulfillment for MIPI camera and display harnesses.
Can HiFlexlinK customize cable lengths, pinouts, or cross-brand connector pairings?
Yes. Every HFL-series MIPI cable supports custom lengths (from compact 40 mm drone links up to 500 mm+ chassis harnesses), 1:1 or custom-mapped pinouts, and hybrid terminations such as I-PEX 20454-030T to ACES 88441. Send your connector part numbers and pinout table to sales@rf-coaxial.com for engineering drawing confirmation.
Are your assemblies compatible with HDZero VTX systems and Sony MIPI camera modules?
es. HFL-HDZ20-20P-P04-AWG42 is engineered as a direct-fit hdzero mipi cable for Race V2 and Shark Byte TX5S.1/TX5M.1/TX5R.1 VTX modules paired with RunCam Micro HDZero and Nano Digital FPV cameras in 40 mm, 80 mm, 120 mm, and 250 mm lengths. For Sony image sensor modules, HFL-KUSL20-30P-P04-AWG42 utilizes the KEL USL20-30SS-0045-C connector.
How should engineers choose between #40, #42, #44, and #46 AWG for a CSI-2 cable?
Select #40 AWG when your csi 2 cable runs longer than 150 mm or requires up to 0.3 A per contact with minimal insertion loss. Choose #42 AWG as the balanced standard for 0.40 mm pitch assemblies. Specify #44 or #46 AWG for tight gimbal bend radii or 0.30 mm pitch Hirose DF56 image sensor headers.
Do HiFlexlinK micro-coaxial cables support MIPI to parallel interface bridge designs?
Yes. Embedded vision systems frequently bridge a high-speed sensor or processor into a MIPI to parallel interface converter IC. Assemblies such as HFL-MC454A-30P-P04-AWG40 and HFL-MC878-30P-P04-AWG40 preserve 50-ohm controlled impedance and differential pair symmetry between the camera module and the bridge board.
What are standard prototype lead times, MOQ, and shipping options?
Custom prototypes ship in 2–10 business days with flexible low-MOQ support, and mass production orders fulfill in 3–4 weeks at up to 15,000 assemblies per week. All shipments are packaged in protective PE inner bags and export cartons via DHL, FedEx, UPS, or TNT.
