Precision Micro-Coaxial Interconnects · 0.30 mm to 0.50 mm Pitch

Custom MIPI CSI-2 & Micro-Coaxial Camera Cable Assemblies

HiFlexlinK engineers high-frequency mipi cable and csi 2 cable harnesses built for low-EMI image transmission across UAV gimbals, embedded vision modules, and industrial displays. Whether you require an ultra-flexible mipi camera cable with 0.30 mm pitch Hirose DF56 terminations, a 20-pin hdzero mipi cable for digital FPV VTX links, or cross-brand assemblies linking a mipi csi 2 cable to a mipi to parallel interface bridge board, every unit is precision-crimped, impedance-verified, and ready for rapid prototyping.

Engineering Capability Envelope


Supported Contact Pitch 0.30 mm / 0.40 mm / 0.50 mm


Micro-Coaxial Wire Range #36 AWG to #48 AWG (UL1354)


Pin Configurations: 10P / 20P / 26P / 30P / 40P / 50P


Controlled Impedance: 50 Ohm +/- 5% (Up to 10 Gbps)


Connector Families: I-PEX, Hirose DF56, KEL USL20, ACES


Prototype Turnaround: 5–10 Business Days

0.30–0.50 mm

Fine-Pitch Termination

Automated micro-stripping and precision solder bar assembly

<= 0.3 dB/cm

Low Insertion Loss @ 5 GHz

Dual-layer foil and braid shielding for clean eye diagrams

100% Tested

Continuity & Pull-Force QC

Netlist open/short screening plus AC 200 V hipot checks

15,000+/wk

Scalable OEM Capacity

Seamless transition from low-MOQ samples to mass production

HiFlexlinK Part Number Nomenclature Guide

Every HiFlexlinK assembly follows a structured five-segment identifier specifying the connector family, active pin count, contact pitch, and micro-coaxial wire gauge. Select any segment below to inspect ordering parameters.

HFL

Brand Prefix

MC345

Connector series

30P

Pin Counts

P04

Pitch(mm)

AWG42

wire Gauge

01. Brand Series Prefix

Identifies HiFlexlinK precision micro-coaxial and high-speed MIPI harness assemblies.

Code: HFL

02. Connector Family Code

Defines the mating plug or hybrid pair (I-PEX, Hirose DF56, KEL USL20, ACES, or HDZero VTX).

MC345 · MC846 · DF56 · MC454A · KUSL20 · MC878 · HDZ20

03. Active Pin Count

Specifies standard populated contacts; custom pinouts from 10P to 50P available per series.

20P · 26P · 30P · 40P · 50P

04. Contact Pitch Code

Centerline terminal spacing in tenths of a millimeter for fine-pitch board matching.

P03 (0.30 mm) · P04 (0.40 mm) · P05 (0.50 mm)

05. Wire Gauge (AWG)

Standard micro-coaxial conductor size; configurable from #36 AWG up to #48 AWG.

AWG40 · AWG42 · AWG44 · AWG46

HiFlexlinK MIPI & Micro-Coaxial Product Catalog

Compare all seven standardized HFL cable assemblies by connector architecture, contact pitch, pin count, wire gauge, and electrical rating. Filter by application or switch to the specification matrix for side-by-side engineering review.

Showing 7 of 7 HiFlexlinK assemblies All lengths customizable · Direct technical RFQ: sales@rf-coaxial.com
HiFlexlinK HFL-MC345-30P-P04-AWG42 0.40mm pitch MIPI CSI-2 drone camera micro-coaxial cable
HFL-MC345-30P-P04-AWG42
0.40 mm Pitch Micro-Coax

Drone & Camera CSI · 0.40 mm Pitch

HFL-MC345-30P-P04-AWG42

MIPI CSI-1 / CSI-2 Micro-Coaxial Camera Cable Assembly

Engineered for UAV drone cameras and compact HD imaging payloads requiring horizontal low-profile mating.

Matching ConnectorI-PEX 20345-030T-32R (Horizontal)
Pitch / Pin Count0.40 mm / 30P (10–40P options)
Wire Gauge (AWG)#40 / #42 / #44 / #46 AWG Coax
Cable LengthCustom (40 mm – 500 mm+)
Mechanical & Electrical RatingsHeight 1.15 mm max (1.00 mm nom.), Depth 5.65 mm, Width 4.80+(0.4xP) mm; 0.1–0.3 A/contact; supports MIPI CSI-1/CSI-2, eDP 2.7 Gbps, V-by-One 4 Gbps, USB 3.1 Gen 1 (5 Gbps).
Lead time: 2–10 days sample Inquire Specs
HiFlexlinK HFL-MC846-20P-P05-AWG40 0.50mm pitch 20-pin MIPI DSI LVDS eDP cable assembly
HFL-MC846-20P-P05-AWG40
0.50 mm Pitch Micro-Coax

High-Speed DSI & eDP · 0.50 mm Pitch

HFL-MC846-20P-P05-AWG40

0.50 mm Pitch 20-Pin MIPI DSI / LVDS / eDP Micro-Coax Assembly

High-bandwidth display and camera interconnect supporting MIPI Gear 3 and eDP HBR3 data rates.

Matching ConnectorI-PEX 20846-020T-02 / 20847-020T-02 (Mates 20849-020E-02)
Pitch / Pin Count0.50 mm / 20-Pin (20P/30P/40P)
Wire Gauge (AWG)#36–#46 AWG (#32/#34 Power)
Cable LengthCustom
Mechanical & Electrical RatingsLock bar 20848 / Shell 3427 compatible; 0.24 A (#42) to 1.0 A (#32/#34 power); supports MIPI Gear 3 (5.8 Gbps), eDP HBR3 (8.1 Gbps), HDMI 2.0 (6 Gbps), USB 3.1 Gen 2 (10 Gbps), Thunderbolt 3 (20 Gbps/lane).
Lead time: 2–10 days sample Inquire Specs
HiFlexlinK HFL-DF56-26P-P03-AWG42 0.30mm pitch Hirose DF56 26-pin image sensor MIPI cable
HFL-DF56-26P-P03-AWG42
0.30 mm Pitch DF56

Image Sensor · 0.30 mm Pitch

HFL-DF56-26P-P03-AWG42

0.30 mm Pitch 26-Pin Ultra-Fine Image Sensor Micro-Coaxial Cable

Ultra-compact CSI-2 cable assembly tailored for space-constrained CMOS image sensors and optical heads.

Matching ConnectorHirose DF56-26P-0.3SD (Receptacle 662-5604-1)
Pitch / Pin Count0.30 mm / 26P (26/30/40/50P)
Wire Gauge (AWG)#38–#46 AWG (Rec. #42–#46 AWG)
Cable LengthCustom
Mechanical & Electrical RatingsCurrent rating 0.20 A (#42 AWG), 0.15 A (#44 AWG), 0.10 A (#46 AWG); operating temperature -35°C to +85°C; supports DF56-26P/30P/40P/50P-0.3SD family.
Lead time: 2–10 days sample Inquire Specs
HiFlexlinK HFL-MC454A-30P-P04-AWG40 0.40mm pitch 20454-030T to ACES 88441 MIPI cable
HFL-MC454A-30P-P04-AWG40
0.40 mm Hybrid Assembly

High-Speed DSI & eDP · 0.40 mm Pitch

HFL-MC454A-30P-P04-AWG40

0.40 mm Pitch I-PEX 20454 to ACES 88441 Hybrid MIPI / eDP Cable

Cross-brand harness connecting MIPI DSI/CSI hosts, eDP panels, and MIPI to parallel interface bridge PCBs.

Matching ConnectorI-PEX 20454-030T to ACES 88441
Pitch / Pin Count0.40 mm / 30P & 40P (10–50P)
Wire Gauge (AWG)#38 / #40 / #42 / #44 / #46 AWG
Cable LengthCustom
Mechanical & Electrical Ratings0.10 A (#44) to 0.50 A (#38) per contact; supports MIPI Gear 3 (5.8 Gbps), eDP HBR3 (8.1 Gbps), HDMI 2.0 (6 Gbps), V-by-One HS 1.4 (4 Gbps); custom cross-pinout mapping supported.
Lead time: 2–10 days sample Inquire Specs
HiFlexlinK HFL-KUSL20-30P-P04-AWG42 KEL USL20-30SS-0045-C 0.40mm pitch MIPI camera cable
HFL-KUSL20-30P-P04-AWG42
KEL USL20 0.40 mm

Image Sensor · 0.40 mm Pitch

HFL-KUSL20-30P-P04-AWG42

KEL USL20-30SS-0045-C 0.40 mm Pitch MIPI Camera & Display Cable

Dedicated 30-pin MIPI camera cable built for Sony camera blocks and industrial LVDS display connectors.

Matching ConnectorKEL USL20-30SS-0045-C
Pitch / Pin Count0.40 mm / 30-Pin
Wire Gauge (AWG)#42 AWG Standard (#38–#46 AWG)
Cable LengthCustom
Mechanical & Electrical Ratings0.25 A/contact; contact resistance <= 100 mOhm; dielectric withstand AC 200 V (1 min); insulation >= 100 MOhm @ DC 250 V; operating temp -40°C to +85°C.
High-volume OEM ready Inquire Specs
HiFlexlinK HFL-MC878-30P-P04-AWG40 30-pin 40AWG 50-ohm shielded MIPI micro-coaxial assembly
HFL-MC878-30P-P04-AWG40
50 Ohm Shielded 40AWG

High-Speed DSI & eDP · 0.40 mm Pitch

HFL-MC878-30P-P04-AWG40

30-Pin 50-Ohm Dual-Shielded 40AWG MIPI / LVDS Micro-Coaxial Assembly

Impedance-controlled 10 Gbps harness with dual-layer foil + braid shielding for noisy RF environments.

Matching ConnectorI-PEX 20878-030T-01 to 20878-030T-01 (1:1)
Pitch / Pin Count0.40 mm / 30-Pin
Wire Gauge (AWG)UL1354 40AWG (7/0.03), 0.35 mm OD
Cable LengthCustom
Mechanical & Electrical Ratings50 Ohm +/- 5% impedance; up to 10 Gbps; insertion loss <= 0.3 dB/cm @ 5 GHz; 50 V AC/DC rating; -40°C to +105°C; dual-layer foil + braid shielding, UL1354 & RoHS compliant.
Lead time: 2–10 days sample Inquire Specs
HiFlexlinK HFL-HDZ20-20P-P04-AWG42 20-pin HDZero digital FPV VTX MIPI camera cable
HFL-HDZ20-20P-P04-AWG42
20P HDZero MIPI Cable

Drone & Camera CSI · 0.40 mm Pitch

HFL-HDZ20-20P-P04-AWG42

20-Pin Digital HDZero FPV VTX & MIPI Camera Micro-Coaxial Cable

Low-latency digital HD video HDZero MIPI cable built for Race V2 VTX, Shark Byte, and long-range FPV wings.

Matching Connector20P Race V2 VTX, Shark Byte TX5S.1/TX5M.1/TX5R.1, RunCam Micro/Nano HDZero
Pitch / Pin Count0.40 mm / 20-Pin
Wire Gauge (AWG)#40 – #48 AWG Micro-Coax
Standard Lengths40 / 80 / 120 / 250 mm / Custom
Mechanical & Electrical RatingsUltra-lightweight micro-coax routing for whoop, toothpick, racing, and fixed-wing UAV airframes; interference-resistant digital HD video feed between MIPI camera and VTX.
Stock lengths + custom Inquire Specs
HiFlexlinK Part Number Connector / Mating Interface Pitch Pin Count Wire Gauge (AWG) Length Action
HFL-MC345-30P-P04-AWG42 I-PEX 20345-030T-32R (Horizontal) 0.40 mm 30P (10–40P) #40 / #42 / #44 / #46 Custom RFQ
HFL-MC846-20P-P05-AWG40 I-PEX 20846 / 20847-020T-02 (Mates 20849) 0.50 mm 20P (20–40P) #36–#46 (#32/#34 Pwr) Custom RFQ
HFL-DF56-26P-P03-AWG42 Hirose DF56-26P-0.3SD (662-5604-1) 0.30 mm 26P (26–50P) #38–#46 (Rec. #42–#46) Custom RFQ
HFL-MC454A-30P-P04-AWG40 I-PEX 20454-030T to ACES 88441 0.40 mm 30P / 40P (10–50P) #38 / #40 / #42 / #44 / #46 Custom RFQ
HFL-KUSL20-30P-P04-AWG42 KEL USL20-30SS-0045-C 0.40 mm 30P #42 Std (#38–#46) Custom RFQ
HFL-MC878-30P-P04-AWG40 I-PEX 20878-030T-01 (1:1 Shielded) 0.40 mm 30P UL1354 40AWG (50 Ohm) Custom RFQ
HFL-HDZ20-20P-P04-AWG42 Race V2 / Shark Byte VTX & HDZero Camera 0.40 mm 20P #40 – #48 AWG 40/80/120/250 mm RFQ

No HiFlexlinK assemblies match your current filter criteria.

Precision Manufacturing, Electrical Testing & Compliance

Fine-pitch micro-coaxial termination demands repeatable mechanical retention and verified RF signal integrity. Every HiFlexlinK assembly is produced in controlled lines with full electrical and environmental screening.

100%

Continuity & Pull-Force Screening

Automated multi-point continuity, open/short, and AC 200 V dielectric withstand testing on every cable, paired with destructive tensile pull-force sampling on each lot.

50 Ohm +/- 5%

TDR Impedance & Insertion Loss

Dual-layer foil and braided ground return shielding controls differential skew and keeps insertion loss at or below 0.3 dB/cm at 5 GHz for 10 Gbps links.

40–500 mm+

Custom Length & Hybrid Pinouts

Exact millimeter length cutting, braided sleeve or Kapton wrapping, and custom cross-brand terminations tailored to your PCB layout and chassis geometry.

RoHS / REACH

Flexible MOQ & Rapid Prototyping

UL1354 micro-coaxial materials rated from -40°C to +105°C, RoHS and REACH compliant, with 2–10 day engineering samples and scalable production MOQ.

Engineering Selection & Procurement FAQ

Technical guidance on connector compatibility, AWG sizing, signal integrity, and prototype fulfillment for MIPI camera and display harnesses.

Can HiFlexlinK customize cable lengths, pinouts, or cross-brand connector pairings?

Yes. Every HFL-series MIPI cable supports custom lengths (from compact 40 mm drone links up to 500 mm+ chassis harnesses), 1:1 or custom-mapped pinouts, and hybrid terminations such as I-PEX 20454-030T to ACES 88441. Send your connector part numbers and pinout table to sales@rf-coaxial.com for engineering drawing confirmation.

Are your assemblies compatible with HDZero VTX systems and Sony MIPI camera modules?

es. HFL-HDZ20-20P-P04-AWG42 is engineered as a direct-fit hdzero mipi cable for Race V2 and Shark Byte TX5S.1/TX5M.1/TX5R.1 VTX modules paired with RunCam Micro HDZero and Nano Digital FPV cameras in 40 mm, 80 mm, 120 mm, and 250 mm lengths. For Sony image sensor modules, HFL-KUSL20-30P-P04-AWG42 utilizes the KEL USL20-30SS-0045-C connector.

How should engineers choose between #40, #42, #44, and #46 AWG for a CSI-2 cable?

Select #40 AWG when your csi 2 cable runs longer than 150 mm or requires up to 0.3 A per contact with minimal insertion loss. Choose #42 AWG as the balanced standard for 0.40 mm pitch assemblies. Specify #44 or #46 AWG for tight gimbal bend radii or 0.30 mm pitch Hirose DF56 image sensor headers.

Do HiFlexlinK micro-coaxial cables support MIPI to parallel interface bridge designs?

Yes. Embedded vision systems frequently bridge a high-speed sensor or processor into a MIPI to parallel interface converter IC. Assemblies such as HFL-MC454A-30P-P04-AWG40 and HFL-MC878-30P-P04-AWG40 preserve 50-ohm controlled impedance and differential pair symmetry between the camera module and the bridge board.

What are standard prototype lead times, MOQ, and shipping options?

Custom prototypes ship in 2–10 business days with flexible low-MOQ support, and mass production orders fulfill in 3–4 weeks at up to 15,000 assemblies per week. All shipments are packaged in protective PE inner bags and export cartons via DHL, FedEx, UPS, or TNT.